
By Matt Thompson, Owner and General Contractor at Construction Corps. U.S. Army combat veteran. Licensed general contractor since 2007, first in California; Florida licensed since 2022 (CGC, FBPE, EC, CFC, MRSR, MRSA). 35+ years in construction.
Last updated November 2026. Construction rules are cited to the Florida Building Code, Residential, 8th Edition (2023), in effect through December 30, 2026, and to 44 CFR 60.3; local rules are cited to each jurisdiction's own documents, checked November 9, 2026. The 9th Edition takes effect December 31, 2026. General information, not engineering or legal advice.
"Key takeaways on Tampa Bay flood zones
- Zones beginning with A or V are the Special Flood Hazard Area, the land FEMA maps as having a 1 percent chance of flooding in any year. Shaded Zone X is moderate hazard (between the 1 percent and 0.2 percent flood); unshaded Zone X is minimal hazard.
- In AE zones, the Florida Building Code sets the lowest floor at or above the base flood elevation plus 1 foot, or the design flood elevation, whichever is higher. Enclosed space below that level is limited to parking, building access, and storage, with flood openings.
- VE zones (wave heights over 3 feet or high-velocity wave action) and Coastal A Zones where designated (waves of 1.5 to 3 feet) require pilings or columns (Coastal A allows a qualifying stem wall), the bottom of the lowest horizontal structural member at or above BFE plus 1 foot or the design flood elevation, no fill for structural support, and breakaway walls of 10 to 20 pounds per square foot below the building.
- Local freeboard varies: St. Petersburg requires 2 feet, per a 2023 city report, for new and substantially improved structures (4 feet for some larger multifamily buildings); Clearwater requires 2 feet above the higher of the FEMA BFE or its 2021 vulnerability assessment elevation; unincorporated Pinellas requires at least 1 foot.
- Zone X is outside the Special Flood Hazard Area, but local rules still apply. The City of Tampa sets a minimum finished floor for living space at 1.5 feet above the crown of the adjacent street, with a waiver process.
- The elevation certificate is the document that proves where a building sits. It is certified by a land surveyor, engineer, or architect and can be prepared from construction drawings, during construction, and at finished construction."
In Tampa Bay, the flood zone printed on a FEMA map decides more about a construction project than almost anything else on the survey. It sets how high the floor has to be, what the foundation can be, what can go under the house, and how much of an existing home can be improved before the whole structure has to meet current flood rules. Two lots on the same street can carry different zones, and two cities a few miles apart can require different heights for the same zone.
This guide explains the four zone labels most Tampa Bay owners see (AE, VE, Coastal A, and X), what the Florida Building Code and federal floodplain rules require in each, and where local governments add freeboard on top. It closes with how to read your zone and your elevation certificate. Every rule is cited to the code, the federal regulation, or the jurisdiction's own document.
What do flood zones AE, VE, Coastal A, and X mean for building?
Flood zones beginning with A or V are FEMA's Special Flood Hazard Area, land with a 1 percent annual chance of flooding. In an AE zone, the Florida Building Code, Residential (8th Edition, 2023) requires the lowest floor at or above the base flood elevation (BFE) plus 1 foot, or the design flood elevation, whichever is higher, and limits enclosed space below to parking, access, and storage with flood openings. A VE zone is a coastal high-hazard area with waves over 3 feet or high-velocity wave action; buildings there must be on pilings or columns with the bottom of the lowest horizontal structural member at or above BFE plus 1 foot or the design flood elevation, no fill for support, and only breakaway walls below. A Coastal A Zone, where designated, covers waves of 1.5 to 3 feet and follows the same coastal rules, with a stem wall option. Zone X is outside the Special Flood Hazard Area and carries no FEMA elevation requirement, though local rules can still set floor heights.
1. The Zones at a Glance
| Zone | What FEMA and the code mean | Elevation reference (FBC-R 8th Ed.) | Foundation and space below |
| AE | Special Flood Hazard Area with a mapped base flood elevation (1 percent annual chance flood). | Lowest floor at or above BFE + 1 ft or the design flood elevation, whichever is higher (R322.2.1). | Foundation per the engineered design (the fill prohibition applies in VE and Coastal A, not AE); enclosed areas below only for parking, access, storage, with flood openings (R322.2.2). |
| VE | Coastal high-hazard area: wave heights over 3 ft, high-velocity wave action, or wave-induced erosion (R322.3). | Bottom of lowest horizontal structural member at or above BFE + 1 ft or the design flood elevation, whichever is higher (R322.3.2). | Pilings or columns; no fill for structural support; space below open or enclosed only with breakaway walls, screening, or lattice (R322.3.3, R322.3.5). |
| Coastal A | Flood hazard area designated for wave heights of 1.5 to 3 ft, or otherwise designated by the jurisdiction (R322.3). Where FEMA maps it, the inland edge of waves over 1.5 ft is the Limit of Moderate Wave Action (LiMWA). | Same as VE where designated (R322.3.2). | Same as VE where designated, except stem wall foundations backfilled to the floor system are permitted if designed for wave action, debris, erosion, and scour (R322.3.3 exception). |
| X (shaded) | Moderate flood hazard: between the 1 percent and 0.2 percent annual chance flood. | No FEMA flood elevation requirement; local rules may apply. | Standard foundations; check local floor-height rules. |
| X (unshaded) | Minimal flood hazard: above the 0.2 percent annual chance flood elevation. | No FEMA flood elevation requirement; local rules may apply. | Standard foundations; check local floor-height rules. |
Two terms carry through every section. The base flood elevation (BFE) is the 1 percent annual chance flood elevation shown on the Flood Insurance Rate Map (FIRM). Freeboard is extra height above the BFE required by the state or local government; the City of Tampa defines the design flood elevation as BFE plus freeboard.
2. AE Zones: Elevate the Floor, Vent the Enclosure
AE zones are A zones with a mapped base flood elevation. The core rules:
- Lowest floor. Under FBC Residential R322.2.1 (8th Edition), the lowest floor of a new or substantially improved home is at or above the BFE plus 1 foot, or the design flood elevation, whichever is higher. Federal rules at 44 CFR 60.3(c)(2) set the national minimum at the base flood level; Florida's code goes higher, and some local governments go higher still.
- Enclosures below. Enclosed areas below the required elevation, including crawl spaces, may be used solely for parking, building access, or storage (R322.2.2). They are not living space.
- Flood openings. Those enclosures need flood openings that let water in and out automatically. Federal minimum criteria call for at least two openings with a total net area of at least 1 square inch for every square foot of enclosed area, with the bottom of each opening no higher than 1 foot above grade (44 CFR 60.3(c)(5)). The Florida code adds that each opening be at least 3 inches in any direction and that covers, louvers, or screens be counted in the net area, or that engineered openings be certified by a registered design professional (R322.2.2).
In practice, an AE-zone home can be built on a raised slab, a stem wall, or an elevated floor system, as the engineered design calls for, with a garage or storage area below the living floor where the design includes one.
3. VE Zones: Pilings, Breakaway Walls, and No Fill
VE zones are coastal high-hazard areas, mapped where wave action is greatest. FBC Residential R322.3 defines them as areas subject to wave heights over 3 feet or to high-velocity wave action or wave-induced erosion. The rules are stricter in five ways:
- Elevation measured to the structure, not the floor. The bottom of the lowest horizontal structural members supporting the lowest floor (excluding pilings, pile caps, columns, grade beams, and bracing) is at or above BFE plus 1 foot or the design flood elevation, whichever is higher (R322.3.2). Because beams and joists sit below the finished floor, this puts the floor higher than the same BFE would in an AE zone.
- Open foundations. Buildings are supported on pilings or columns designed under ASCE 24 for combined wave and wind loads, including scour, and the foundation design is prepared and sealed by a design professional (R322.3.3). Federal rules also require an engineer or architect to certify the design (44 CFR 60.3(e)(4)).
- No fill for support. Fill may not be used for structural support (R322.3.2, item 5; 44 CFR 60.3(e)(6)). Minor grading and small amounts of fill for landscaping, drainage, and support of parking slabs, pool decks, patios, and walkways are permitted.
- Breakaway walls only. The space below is either open or enclosed with insect screening, open lattice, or walls designed to break away under flood loads without damaging the elevated building. Breakaway walls must have a resistance of not less than 10 and not more than 20 pounds per square foot; where the code's wind loads exceed 20 pounds per square foot, a registered design professional documents that the walls collapse under less than base flood water loads and that the elevated building and foundation resist wind and flood loads together. Electrical, mechanical, and plumbing components may not be mounted on or run through breakaway walls, and breakaway walls must also have flood openings (R322.3.5).
- No basements, limited use below. Basement floors below grade on all sides are prohibited (R322.3.2, item 2), and enclosed space below may be used only for parking, building access, or storage (44 CFR 60.3(e)(5)). Federal rules also require new construction to be landward of the reach of mean high tide and prohibit man-made alteration of sand dunes and mangrove stands that would increase flood damage (44 CFR 60.3(e)(3) and (e)(7)).
Detached garages and accessory structures in these zones either meet the same elevation, or stay below it only if they are used solely for parking or storage, are one story and no larger than 100 square feet, and are anchored against flood loads (R322.3.2, item 4).
4. Coastal A Zones and the LiMWA
A Coastal A Zone is part of the A-zone area where waves are smaller than in a VE zone but still damaging. FBC Residential R322.3 defines it as a flood hazard area designated as subject to wave heights between 1.5 and 3 feet, or otherwise designated by the jurisdiction, and applies the coastal high-hazard rules (R322.3.1 through R322.3.10) to buildings in Coastal A Zones where designated. FEMA's mapping guidance calls the inland limit of waves greater than 1.5 feet the Limit of Moderate Wave Action (LiMWA), shown as a line on FIRMs where FEMA has mapped it.
The key difference from a VE zone is the foundation: in a Coastal A Zone, a stem wall foundation supporting the floor system and backfilled with soil or gravel to the underside of the floor is permitted, if designed for wave action, debris impact, erosion, and local scour (R322.3.3, exception). Where a stem wall is used, the top of the foundation wall supporting the slab is treated as the bottom of the lowest horizontal structural member for the elevation rule (R322.3.2).
Whether Coastal A rules apply to your lot depends on whether your jurisdiction designates the area. The City of Tampa's substantial improvement form, for example, covers AE, Coastal A, and VE zones. If your FIRM panel shows a LiMWA line near your parcel, ask the floodplain office which rules it applies before design.
5. Zone X: Outside the SFHA, Not Outside the Rules
FEMA labels moderate-hazard areas as shaded Zone X (or Zone B on older maps) and minimal-hazard areas as unshaded Zone X (or Zone C). Neither is part of the Special Flood Hazard Area, so the FEMA and Florida Building Code flood elevation rules described above do not apply there unless the jurisdiction has designated an additional flood hazard area.
Local rules can still set floor heights. The City of Tampa's finished floor elevation waiver form describes Chapter 21 of the City Code as requiring the finished floor of all living space to be at least 1.5 feet above the crown of the adjacent street, and all other floors at least 1.0 foot above the crown, with a waiver process. Other jurisdictions set their own grading and floor rules; confirm with the building department before you set a slab height.
Zone X also does not mean a property will not flood. Shaded Zone X is defined by the 0.2 percent annual chance flood, and local drainage, storm surge beyond the mapped event, and map changes all matter. Building a little higher than the minimum is a design choice worth pricing.
6. Freeboard by Jurisdiction
The Florida Building Code sets a statewide minimum of BFE plus 1 foot. Local governments can require more, and several in Pinellas County do.
| Jurisdiction | Required elevation (new and substantially improved) | Source |
| Florida Building Code (statewide minimum) | Lowest floor at or above BFE + 1 ft or the design flood elevation, whichever is higher (AE); bottom of lowest horizontal structural member to the same level in VE and Coastal A. | FBC-R 8th Ed. R322.2.1, R322.3.2 |
| City of St. Petersburg | 2 ft of freeboard for all new or substantially improved structures; 4 ft for some multifamily buildings with 3 or more units. | City Repetitive Loss Area Analysis report (October 2023); confirm current code with the city |
| City of Clearwater | 2 ft above the higher of the FIS/FIRM BFE or the RESTORE Act Vulnerability Assessment (2021) elevation. | City floodplain administrator, November 2026 |
| Unincorporated Pinellas County | At least 1 ft above the BFE. | pinellas.gov, Construction in a Floodplain |
| City of Belleair Beach | FBC elevation of BFE + 1 ft; building height measured from BFE + 1 ft (RL district II). | City Code Sec. 94-209 |
| North Redington Beach and Redington Beach | BFE + 1 ft of freeboard. | SAFEbuilt (building department for both towns), November 2026 |
| City of Tampa | Design flood elevation = BFE + freeboard; no local freeboard above the FBC minimum found in the city's published flood documents. Confirm with Construction Services. | City private provider flood program notice (2026) |
| Unincorporated Hillsborough County | No local freeboard above the FBC minimum found in the county's published requirements. Confirm with the county floodplain office. | hcfl.gov SFHA requirements |
Freeboard also changes the substantial improvement math indirectly: once a project crosses the threshold, the whole structure must be brought up to the required elevation, so a higher local freeboard makes crossing the threshold more expensive.
7. Substantial Improvement Thresholds
Work on an existing home in a Special Flood Hazard Area is tested against the substantial improvement rule. The federal definition is improvement costs that equal or exceed 50 percent of the market value of the structure before the work (44 CFR 59.1). Two of the jurisdictions below set a lower trigger, and Clearwater adds an earlier review:
| Jurisdiction | Threshold and valuation |
| Unincorporated Pinellas County | 49 percent of the market value of the structure; value reconsideration and independent appraisal options per county guidance. |
| City of St. Petersburg | 49 percent of the structure's value. |
| City of Clearwater | 50 percent (NFIP minimum), with an administrative review once a project reaches 40 percent. |
| City of Tampa | 50 percent of the structure's depreciated value, from the Hillsborough County Property Appraiser listing or a certified appraisal; costs from the current ICC Building Valuation Data table. |
| Unincorporated Hillsborough County | 50 percent of market value; market value is 120 percent of the Property Appraiser's assessed value or a certified appraisal. |
Under FL Statute 163.31795, created in 2025, local governments may not aggregate improvement costs over multiple years when making these determinations. Pinellas County also warns that unnecessary demolition can push a property over its threshold.
8. Reading Your Flood Zone and Elevation Certificate
- 1. Find the zone and BFE. Look up the address on FEMA's Flood Map Service Center (msc.fema.gov). The FIRM panel shows the zone, the BFE where one is mapped (AE and VE zones), and the LiMWA line where mapped. Pinellas County's Flood Information Services line, (727) 464-7700, helps with zone questions in the county.
- 2. Confirm the jurisdiction. The freeboard and threshold that apply depend on which government issues the permit, not the mailing address.
- 3. Read the elevation certificate. FEMA's Elevation Certificate (Form FF-206-FY-22-152) records the building's surveyed elevations so they can be compared with the BFE. Section C states whether the elevations are based on construction drawings, a building under construction, or finished construction, and Section D is signed and sealed by a land surveyor, engineer, or architect authorized by state law to certify elevation information. The form also requires photographs showing the foundation and, where present, the flood openings.
- 4. Expect certificates during construction. The City of Tampa requires an elevation certificate with a construction permit application in a Special Flood Hazard Area, and under its current private provider rules for flood zones, the city performs inspections up to the design flood elevation until it approves the required under-construction elevation certificate. Unincorporated Hillsborough requires elevation certificates at three stages.
- 5. Ask the floodplain office early. Zone boundaries, Coastal A designations, and local freeboard all affect the design. A short call before design is cheaper than a redesign after plan review.
9. What This Means for Additions, Remodels, and New Homes
- New homes and teardown rebuilds. The zone and the local freeboard set the floor height and foundation type from the start. In VE and designated Coastal A Zones, that means pilings or columns (or a qualifying stem wall in Coastal A) and an engineered foundation design.
- Additions. An addition is an improvement to the existing structure, so its cost counts toward the substantial improvement threshold. If it crosses the threshold, the whole house must comply; if it stays under, confirm with the floodplain office how the addition itself must be built.
- Remodels and storm repairs. Interior remodels and repairs count toward the threshold too. Keep the scope and the cost breakdown clear, and avoid unnecessary demolition.
- Enclosures and garages. Below-floor space stays parking, access, or storage, with flood openings in AE zones and breakaway walls in VE and Coastal A Zones. Finishing it as living space is not permitted.
Construction Corps works plans first: zone, BFE, local freeboard, and the substantial improvement position are checked before design, so the house is planned around a realistic budget. The majority of the plans we produce for homeowners go on to be built by us. We also produce plans for other contractors, who build those projects themselves.
10. Frequently Asked Questions
What is the difference between flood zone AE and VE?
Both are part of FEMA's Special Flood Hazard Area with a mapped base flood elevation. A VE zone is a coastal high-hazard area with wave heights over 3 feet or high-velocity wave action, so the Florida Building Code requires pilings or columns, measures elevation to the bottom of the lowest horizontal structural member, prohibits fill for structural support, and allows only breakaway walls below. In an AE zone, the lowest floor is elevated to BFE plus 1 foot or the design flood elevation, and enclosures below need flood openings.
What is a Coastal A Zone?
Under Florida Building Code, Residential R322.3 (8th Edition), a Coastal A Zone is a flood hazard area designated as subject to wave heights between 1.5 and 3 feet, or otherwise designated by the jurisdiction. Where designated, buildings follow the coastal high-hazard rules, except that stem wall foundations backfilled to the floor system are permitted if designed for wave action, debris, erosion, and scour. FEMA maps the inland edge of waves over 1.5 feet as the Limit of Moderate Wave Action (LiMWA).
Do I have to elevate my house in Zone X?
Not under FEMA or Florida Building Code flood rules, because Zone X is outside the Special Flood Hazard Area. Local rules can still apply: the City of Tampa sets a minimum finished floor for living space at 1.5 feet above the crown of the adjacent street, with a waiver process. Confirm floor-height and grading rules with your building department.
How high above the base flood elevation do I have to build in St. Petersburg?
The City of St. Petersburg's October 2023 Repetitive Loss Area Analysis report states the city requires 2 feet of freeboard for all new or substantially improved structures and 4 feet for some multifamily buildings with 3 or more units. Confirm the current requirement with the city's floodplain staff at [email protected].
What is freeboard in Clearwater?
The City of Clearwater requires 2 feet of freeboard above the higher of the FIS/FIRM base flood elevation or the elevation from the city's RESTORE Act Vulnerability Assessment (2021), according to the city's floodplain administrator. Confirm with the city for your parcel.
What are breakaway walls?
Breakaway walls are non-structural walls below an elevated building in a VE or Coastal A Zone, designed to collapse under flood loads without damaging the building or its foundation. Under FBC Residential R322.3.5 and 44 CFR 60.3(e)(5), they have a design resistance of not less than 10 and not more than 20 pounds per square foot unless a registered design professional certifies a higher design. Utilities may not be mounted on or run through them, and the space they enclose is limited to parking, access, and storage.
What are flood vents and how many do I need?
Flood openings, often called flood vents, let floodwater enter and leave an enclosure below the elevated floor so the walls are not pushed in. Federal minimum criteria require at least two openings with a total net area of at least 1 square inch per square foot of enclosed area, with the bottom of each opening no higher than 1 foot above grade (44 CFR 60.3(c)(5)). Engineered openings certified by a registered design professional are an alternative.
Who prepares an elevation certificate?
A land surveyor, engineer, or architect authorized by state law to certify elevation information signs and seals FEMA's Elevation Certificate. The certificate can be based on construction drawings, a building under construction, or finished construction, and includes photographs of the foundation and any flood openings.
Does the 9th Edition of the Florida Building Code change these rules?
The 9th Edition takes effect December 31, 2026. The rule that the lowest floor sit at or above BFE plus 1 foot or the design flood elevation carries into the 9th Edition for flood hazard areas other than Coastal A Zones, which are handled in the coastal provisions. Projects permitted on or after that date should confirm 9th Edition section numbers and text with the building department.
Who designs and builds in Tampa Bay flood zones?
Construction Corps designs, permits, and builds additions, remodels, ADUs, and storm rebuilds across Pinellas, Hillsborough, Pasco, and Sarasota counties as a veteran-owned design-build general contractor based in Clearwater, holding Florida licenses CGC1530192, FBPE39242, EC13013956, CFC1432954, MRSR5676, and MRSA5772. We check the zone, BFE, local freeboard, and substantial improvement position before design. Call (727) 999-1855.
Start with the zone, not the floor plan
Construction Corps is a veteran-owned design-build general contractor based in Clearwater, serving Pinellas, Hillsborough, Pasco, and Sarasota counties. Before design, we confirm the flood zone, base flood elevation, local freeboard, and where the project sits against the substantial improvement threshold, so the foundation and floor height are right from the first drawing
Planning work in a flood zone? Send us the address and your elevation certificate if you have one, or get a ballpark in about 90 seconds at constructioncorps.com/estimator.
- Construction Corps, Inc. | 2054 Weaver Park Drive, Clearwater, FL 33765
- Phone: (727) 999-1855 | Web: constructioncorps.com
- Licenses: CGC1530192 | FBPE39242 | EC13013956 | CFC1432954 | MRSR5676 | MRSA5772
About Construction Corps
Construction Corps, Inc. is a veteran-owned, full-service design-build general contractor headquartered at 2054 Weaver Park Drive, Clearwater, Florida 33765. Founded in 2022 and led by Matt Thompson, a U.S. Army combat veteran (Infantry, 11B) with 35+ years of construction experience, first licensed as a general contractor in California in 2007 and licensed in Florida since 2022, Construction Corps serves residential and commercial clients across the Tampa Bay region, including Pinellas, Hillsborough, Pasco, and Sarasota counties. The firm is an SBA-certified Service-Disabled Veteran-Owned Small Business (SDVOSB) and Veteran-Owned Small Business (VOSB), and is certified by the National Veteran Business Development Council (NVBDC) as a Service-Disabled Veteran-Owned Business (SDVOB). Construction Corps delivers design-build as one company, as full projects or plans first, holding Florida licenses CGC1530192 (general contractor), FBPE39242 (Florida Board of Professional Engineers), EC13013956 (electrical contractor), CFC1432954 (plumbing contractor), MRSR5676 (mold remediation), and MRSA5772 (mold assessor). Published project pricing is available at constructioncorps.com/estimator. Phone (727) 999-1855.
Sources cited
- Florida Building Code, Residential, 8th Edition (2023), Section R322 (R322.2.1, R322.2.2, R322.3, R322.3.2, R322.3.3, R322.3.5): codes.iccsafe.org/content/FLRC2023P1
- 44 CFR 60.3, Flood plain management criteria for flood-prone areas (paragraphs (c)(2), (c)(5), (e)(3) through (e)(7)), and 44 CFR 59.1 (substantial improvement): ecfr.gov
- FEMA, Flood Zones glossary (Special Flood Hazard Area, Zone X shaded and unshaded): fema.gov/about/glossary/flood-zones
- FEMA, Guidance for Flood Risk Analysis and Mapping, FIRM graphics (Limit of Moderate Wave Action): fema.gov
- FEMA Elevation Certificate, Form FF-206-FY-22-152 (Sections C and D, photograph requirements): fema.gov
- City of St. Petersburg, Repetitive Loss Area Analysis Annual Report (October 2023), freeboard and 49 percent rule: stpete.org
- City of Clearwater floodplain administrator (November 3, 2026), freeboard and substantial improvement review; Community Development Code Chapter 51
- Pinellas County, Construction in a Floodplain (1 foot above BFE) and substantial damage and improvement guidance: pinellas.gov
- City of Belleair Beach Code Sec. 94-209; SAFEbuilt for North Redington Beach and Redington Beach (November 2, 2026)
- City of Tampa, Private Provider Program Changes for Projects in FEMA Special Flood Hazard Areas (2026), Finished Floor Elevation Waiver form (Chapter 21), Flood Protection page, and FEMA Substantial Improvement and Damage form: tampa.gov
- Hillsborough County, Special Flood Hazard Area requirements (substantial improvement valuation, elevation certificates): hcfl.gov
- FL Statute 163.31795 (substantial improvement determinations; no aggregation of costs), 2026 Florida Statutes: flsenate.gov



